WH Series PTO Shaft Walterscheid Replacement WH2300 WH2400 WH2500 WH2600 Agricultural Tractor PTO Driveline
The PTO shaft we produce can perfectly replace the Walterscheid brand’s PTO shaft, because our PTO shaft has a very high level of quality, performance, and reliability.
Our produced PTO shaft can perfectly replace the Walterscheid brand PTO shaft, providing you with a more efficient, reliable, and durable PTO shaft solution. Whether you are a high-end tractor brand or an ordinary tractor brand, we can meet your needs.
WH Series PTO Shaft
The advantages of this Walter scheid PTO drive shaft are long service life, convenient use, and good safety performance. For decades, Walterscheid has been the guarantee of the highest quality. The size of the W series is suitable for powertrain tasks, from simple to complex. It left a deep impression on users with its sturdy design and high reliability for daily use. Another advantage is that all components in the PTO drive shaft WH series can be easily replaced to improve ease of use, or if spare parts are needed.
|WH2300||1130||SD15||0v||QSG||1 3/8” x 6
WH PTO Parts
PTO Shaft Adjustment for Tractor
Pay attention to the length of the PTO shaft when you first mount it. A PTO shaft that is too long will break the machine or the transmission of the tractor. A
PTO shaft that is too short will fall apart in the middle.
1. Mount the TrunkPump on the threepoint hitch of the tractor.
2. Lift the three point hitch so that the power intake shaft of the
TrunkPump is the same height as the PTO of the tractor. The PTO and the power intake should be closest to each other at that position. Turn off Tractor!
3. Measure the distance between the notch of the Tractor’s sixsplined shaft to the notch of the six splined shaft of the TrunkPump. This will be the longest possible compressed length of the PTO shaft.
4. Subtract two inches from this measurement. (e.g. If you measured 24 inches, you subtract 2 inches … 24” - 2” = 22”) This number will be the compressed length of the PTO shaft.
5. The compressed length of the shaft you purchased (if you purchased this from TrunkPump) is 27” inches “notch to notch.” Take 27 inches and subtract your answer from #4. The difference between the two is the amount you need to cut off the tip of the two parts of the PTO shaft. (e.g. In our example we have 27” 22” = 5” You would need to cut 5” inches off of both ends of the PTO shaft)
6. Be sure to cut both halves of your PTO shaft to the same length. Cut the guards to the same length as well. File sharp edges off the shaft tubes and guards so they can easily slide into one another.
Cutting the PTO Driveline
Determine the excess length of the transmission system
PTO shaft ends installed to mark overlap
Firstly, connect the implement to the 3-point linkage of the tractor. Adjusting the 3-point linkage for the PTO on the tractor
At the same height as the implement, the distance between them is minimized. Paste The two ends of the PTO are connected to the tractor and implement, and the PTO is divided into two parts . Adjust the direction of the axes so that they pass through each other as parallel as possible.
Marking the PTO to Cut
Using a straight edge, transfer a mark from the end of the tube section to the other section as shown here and in the manual that comes with the PTO. This line represents how much the shafts are too long to fit together. The manufacturer of the PTO shafts recommends adding 40mm (about an inch and a half) to the amount to cut off the plastic tube and the steel telescoping tube of each half of the PTO
mark overlap length
The overlap length is 150mm for this example. Add 40mm to that for our cutoff length. The amount to cut off is 190mm. This example is in metric because the instructions given by the manufacturer of the PTO are in metric
cut off length marked
Cutting the PTO
Cut the 190mm length of plastic tube on one of the shaft ends, leaving the steel shaft inside not cut.
Use the cut length of plastic tube to mark the remaining 3 cuts. Align the end of the tube with the end of the shaft.
align end of tube to end of shaft
Use the other end of the tube to mark the cut length on the steel shaft
use tube to mark the cut length to steel shaft
Now the shaft is marked to cut the same length as the plastic tube
When cutting the steel shaft, clamp it in a vise using the discard end to clamp on. The type of saw could be abrasive cut-off, reciprocating with a fine tooth blade for metal, a powered band saw for metal or the common hacksaw shown here. Be careful and wear eye protection.
Repeat the process so that both shaft halves have had the same length removed. If your shaft has 3 points instead of the 2 shown here, look for the one with the flat - it is different than the other two. The ones with the flat must align or they will not fit together.
De-burr the PTO
When the cut is complete, there will be shavings and burrs that need to be removed.
Using a file, grinder, wire wheel, flap wheel, grinding disk or sandpaper, de-burr the shafts after you cut them.
Clean and Lubricate PTO
Before re-assembling the shafts, push a rag down into each shaft and then around the outside with something like a used hacksaw blade, then remove the rag to clear out the debris and shavings.
Now that both shaft halves are clean inside and out, wipe off that used hacksaw blade and spread some allpurpose grease into the inside of the bigger shaft. The smaller shaft will fit inside the bigger shaft. Spread it out so it does not just get pushed down to the end.
We not only provide pto shafts, but also provide related pto accessories, as well as gearboxes for use with pto shafts. We can provide you with solutions for all the agricultural machinery accessories you need to protect your agricultural machinery
Accessories of PTO Shaft
Write Your Review