Логотип XINLAN Китайский редукторный завод

45HP Post Hole Digger Gearbox XL-GT40U PHD 3:1

The gearbox is one of the important components of a pile excavator, usually located at the rear of the body, connecting the reducer and transmission shaft to transmit the power of the engine to the excavation system and other moving components. Gearboxes are usually made of high-strength steel with sufficient strength and stability to withstand high torque and long-term operation.

Post Hole Digger Gearbox XL-GT40U

The gearbox is one of the important components of a pile excavator, usually located at the rear of the body, connecting the reducer and transmission shaft to transmit the power of the engine to the excavation system and other moving components. Gearboxes are usually made of high-strength steel with sufficient strength and stability to withstand high torque and long-term operation.

 45HP Post Hole Digger Gearbox XL-GT40U PHD 3:1 45HP Post Hole Digger Gearbox XL-GT40U PHD 3:1
Пункт XL-GT40U
Соотношение 3:1
Зубы  33/11
Модуль 5.0
Мощность(hp) 45
Номинальный вход 540 об/мин
Описание входа/выхода 1 3/8 Z6 Оптическая ось
Вес (N.W) 28KG

Gearbox in Копатель почтовых ям

45HP Post Hole Digger Gearbox XL-GT40U PHD 3:1

① Auger bit: С помощью острой головки он может вскапывать почву, причем обычно предлагаются различные размеры и глубина.

② Post hole digger gearbox: An important part of transmitting power from the tractor to the drill bit. The gearbox can transmit power to the drill bit through the tractor’s power take-off shaft, causing it to rotate to dig holes. Typically, transmissions have multiple speed settings to adjust speed and torque for different soil types and depths.

③ Three-point boom pole: Для обеспечения устойчивости оборудования в процессе эксплуатации оно может быть подсоединено к трехточечной соединительной раме, обычно подсоединяемой к задней части трактора. Конструкция трехточечной соединительной рамы также помогает контролировать положение и глубину отверстий, обеспечивая регулировку угла и глубины.

④ Карданный вал: Вал отбора мощности (ВОМ) подсоединяется к задней части трактора и обеспечивает необходимый крутящий момент и скорость вращения для привода бура.

How to Install the Gearbox to Post Hole Digger?

45HP Post Hole Digger Gearbox XL-GT40U PHD 3:1

  1. Use tractor’s hydraulic lift to raise boom. Separate the 2 driveline halves. Attach outer driveline yoke to tractor PTO by pushing in the quick detachment pin and
    sliding drive shaft onto tractor. Attach inner driveline yoke to post hole digger gearbox by using the 3/8”x3” grade 2 shear bolt   or the 1/4”x2.5” grade 2 shear bolt   and elastic stop nut.
  2. Raise and lower digger (without the auger attached) with the tractor’s 3 point quick hitch to ensure the driveline has at least 2” from bottoming out in its shortest working position and has the minimum 6” overlap in its longest working position.  of this manual, if it is determined that the driveline is too long and needs to be shortened. Contact your local dealer if it is determined that the driveline is too short for your tractor. If the driveline is of the correct length proceed to step 3 below.
  3.  Apply multi-purpose grease to the inside of the outer driveline shaft and reassemble the two shafts.
  4. Note: The driveline requires the use of a safety set screw  to prevent it from coming off the gearbox in the event that the shear bolt is sheared. Turn safety set screw all the way in the PTO shaft and into the groove of the input shaft of the gearbox. Back out set screw no more than 1/4 turn and secure with hex nut.
  5. The driveline should now be moved back and forth to ensure that both ends are secured to the tractor and the post hole digger gearbox.
  6. Install both driveline safety chains. One should be hooked in a hole on the outer driveline yoke shield and to the tractor to restrict outer shield rotation. The second one should be hooked in a hole on the inner driveline yoke shield and to the post hole digger to restrict inner shield rotation.

Редуктор 

Семинар

Сопутствующий продукт

Карданный вал

Коробка передач сельскохозяйственной техники используется совместно с карданным валом, который передает мощность на коробку передач, а затем приводит в действие сельскохозяйственную технику. Мы также производим и продаем карданные валы для удовлетворения ваших потребностей!

Нажмите на изображение, чтобы узнать больше↓

ru_RUРусский