Agricultural PTO Shaft for Round Balers New Holland BR7050 BR7060 BR7070 BR7080 BR7090

分类: 标签:

The power of the baler is usually transmitted through the PTO (Power Take off) shaft. PTO shaft is a type of shaft, usually installed on the power output shaft of tractors or agricultural machinery, through which power can be obtained from the power output shaft.

In a baler, the PTO shaft is usually connected to a reducer, which then transmits power to the drive shaft of the baler. The function of the reducer is to convert the high-speed rotation of the power output shaft into the low-speed rotation of the baler, in order to better control the movement of the baler.
In some balers, the PTO shaft can be manually operated to control the transmission of power. In this case, the driver can control the rotation of the PTO shaft through the joystick or button, thereby controlling the movement of the baler.

圆形打包机的PTO轴

The power of the baler is usually transmitted through the PTO (Power Take off) shaft. PTO shaft is a type of shaft, usually installed on the power output shaft of tractors or agricultural machinery, through which power can be obtained from the power output shaft.

In a baler, the PTO shaft is usually connected to a reducer, which then transmits power to the drive shaft of the baler. The function of the reducer is to convert the high-speed rotation of the power output shaft into the low-speed rotation of the baler, in order to better control the movement of the baler.
In some balers, the PTO shaft can be manually operated to control the transmission of power. In this case, the driver can control the rotation of the PTO shaft through the joystick or button, thereby controlling the movement of the baler.

In other balers, the PTO shaft is usually controlled through an automatic control system. This automatic control system can detect the status and needs of the baler through sensors and controllers, and transmit power as needed. This automatic control system is commonly referred to as the "PTO automatic switching system", which can automatically switch between different power transmission modes to maximize the efficiency and reliability of the baler.

Agricultural PTO Shaft for Round Balers New Holland BR7050 BR7060 BR7070 BR7080 BR7090

New Holland calls for CAT3, CAT4 and CAT5 constant velocity drivelines depending on model, with various torque limiters.
Input shafts are 1.375-6 or 1.375-21. Please call 800-824-0706 with your specifications.

推荐的 PTO 轴

  • CAT 3, 4, 5 PTO Shaft Constant Velocity

Available for tractors using 1.375-6 or 1.375-21

Input shaft is 1.375-6 or 1.375-21

Other combinations are available.

 

Please call for information on cutout clutches.

MODEL
HP
CAT
TORQUE DEVICE
BR7050
40
CAT3
SHEARBOLT
BR7050 HM
45
CAT3
SHEARBOLT
BR7060
60
CAT4
SHEARBOLT
BR7060 STD
60
CAT4
SLIP CLUTCH
BR7060 SS
65
CAT4
SLIP CLUTCH
BR7060 CC
100
CAT5
CUTOUT CLUTCH
BR7070
70
CAT4
SLIP CLUTCH
BR7070 SS
70
CAT4
SLIP CLUTCH
BR7070 CC
105
CAT6
CUTOUT CLUTCH
BR7080
70
CAT5
SLIP CLUTCH
BR7090
80
CAT5
SLIP CLUTCH

Our recommendation is not always New Holland Original Equipment. Sometimes it's an upgrade.

Agricultural PTO Shaft for Round Balers New Holland BR7050 BR7060 BR7070 BR7080 BR7090

  • Parts for PTO Shaft

Slip Clutches

FT Clutches for 1.375-6 Spline Input

Universal Size Torque nm BYP  Friction Clutch
CAT3 / S4 1000nm BYP  Friction Clutch
CAT4 / S5 1200nm
CAT4 / S6 1800nm
CAT5 / S8 1450nm

Shear Bolt Clutches

Shear Bolts Clutches for 1.375-6 spline input

Universal Size Torque nm BYP Shear Bolt Clutch
CAT3 / S4 1700nm BYP Shear Bolt Clutch
CAT4 / S6 2400nm
CAT4 / S6 2700nm

 

Cutting PTO Shaft for use on Round Baler

Most important : minimum overlap 15 cm , end play minimum 4 cm

Cutting PTO Shaft for use on Round Baler

Procedure for cutting the PTO shaft to the correct 长度
If the PTO shaft is too long it might bind when the three point hitch is lifted up.Damage might be caused to the bearing of the rotavator or to the PTO of the tractor. Ifthe PTO shaft is too long it mustbe cut.
Both PTO halves must be shortened by equal amounts.

Step1. Mount the Rotavator on the three-pointhitch of the tractor.
Step2. Lift the three point hitch so that the powerintake shaft of the rotavator is almost on the sameheight as the PTO of the tractor. The PTO and the power intake should be closest to each other atthat position. And the top of rotavator should belevel to ground(horizontal)
Step 3. Stop the tractor engine and remove thekeys.
Step 4. Pull the PTO 轴 apart.Connect one halfof the PTO shaft to therotavator  so that thelocking pin is locked in place. Place theother  halfof the PTO shaft flush with the end of the tractor'sPTO. Lay the ends side by side as shown in thefigure to the right. Mark on the shield how muchmust be cut off. The tubes must be so shortened

Safety Reminder When Using the PTO Shaft

Keep safety shields securely fastened on equipment. Safe operation of the PTO is not possible without these shields in place. A sudden slip or fall could throw a worker directly onto the unshielded rotation shaft. Also, those who are unfamiliar with the equipment, may not recognize the danger of the power shaft.

Wear snug fitting clothes when working around power shafts. Loose clothing can catch in or be wrapped around the power shaft. Do not step over an operating PTO. A sudden slip or a loose shoe string could cause the worker to become entangled in the PTO shaft. Long hair may also become entangled in a PTO shaft. Hair should be pulled back out of the way.

Most power shafts can be extended. These shafts are usually constructed with a square shaft inserted into a housing or casing. It is important that at least 5 ½ inches of the sliding shaft remain in the housing when the power shaft is connected to the tractor. This reduces the possibility of the shafts separating while the tractor is in motion. If the shaft splits, the portion of the shaft connected to the tractor is free to whirl at high speeds, endangering the worker and tractor. If the shaft does separate, disengage the PTO immediately and stop the tractor. Use extreme caution when operating equipment with a separable PTO shaft. Never hook 540 rpm equipment to a 1000 rpm PTO or vice-versa.

我们不仅提供 pto 轴,还提供相关的 pto 配件以及与 pto 轴配套使用的变速箱。我们可以为您提供保护农业机械所需的所有农业机械配件解决方案

农用齿轮箱

PTO 轴附件

zh_CN简体中文